MON10T1
23.09.2011 ©Velleman nv
4
A Display F video select button (AV1/AV2)
B DOWN button (j) G power button
C MENU button H monitor plug
D UP button (i) I computer plug
E IR receiver
1 yellow RCA Video 1 input (AV1) 5 red lead “+” 12Vdc
2 yellow RCA Video 2 input (AV2) 6 black lead “-” GND
3 red RCA Audio input right 7 blue lead reverse lamp
4 white RCA Audio input left 8 8-pin monitor jack
6. Installation
The car connection should be carried out by a qualified person only.
• Choose a mounting location, depending on the purpose of the monitor. When used to connect
backing-up or parking camera(s), the driver should have a clear view of the display. For all other
purposes make sure the driver is not distracted by images and/or sound from the system.
• Mount the mounting bracket and attach the monitor to the bracket with the screw or install the
monitor in a headrest using the included frame. When choosing the second option, have the
installation done by a qualified person! The dealer will not accept responsibility for any damage to the
cars interior.
• Connect the monitor jack [8] with the monitor plug [H].
• Connect a camera/video/DVD… (not incl.) to a video input [1][2]. Connect the sound output of that
device to the audio inputs [3][4].
• Make sure the engine is switched off.
• Connect the red +12VDC power cable [5] to the +12VDC power system of the car. Make sure there
is no power on the connection wire (remove fuse).
• Connect the black ground cable [6] to the car ground.
• The monitor can switch on/over to AV2 automatically when reverse gear is selected. To enable this
functionality, connect the blue reverse cable [7] to the reverse gear power circuit. Make sure there
is no power on the connection wire (remove fuse).Connect the backing-up camera to video input
AV2 [2].
• Apply power to the system (re-insert fuses).
Note: the MON10T1 can also be used as a computer/laptop monitor. Connect the computer plug [I] to
the computer using the included cable. When necessary (e.g. no 12Vdc available from car battery),
connect a 12VDC power supply (not incl.) to the power plug on the cable.
7. Use
• Switch on the monitor by pressing the ON/OFF button on the monitor [G] or remote control ( ).
Note that when connection to the reverse gear system is made, the monitor switches on
automatically when reverse gear is selected.
• Select the video channel (AV1, AV2 or VGA) by pressing the video select button on the monitor [F]
or remote control.
Note: select VGA to see images from a connected computer.
• Press the mode select button on the remote control to select the monitor aspect ratio: 16:9 or 4:3.
• Press the menu button [C] on the monitor or remote control to enter monitor setup. Use the menu
button [C] to navigate through the settings; use the up (i) [D] or down (j) [B] buttons to change
the settings (on the remote control, use the f resp. e buttons).
Menu option setting value
BRIGH
brightness 0 ~ 40
CONTRAS
contrast 0 ~ 40
COLO
colou
0 ~ 40
MODE aspect ratio 16:9 or 4:3
IR SELEC
*
select IR sound output IR1 – IR2 - OFF
RESE
reset reset monitor to factory defaults
* Set the same channel on the IR headphone (MONT/HP, not incl.) with the channel selector.
IR1 = channel A, IR2 = channel B.
(10 paginas)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales