Velleman MONxTA1 Manual de usuario descargar pdf (Pagina 4)

MONxTA1

V. 01 – 07/03/2012 ©Velleman nv

1 yellow RCA Video 1 input (AV1) 5 red lead “+” 12Vdc

2 yellow RCA Video 2 input (AV2) 6 black lead “-” GND

3 red RCA Audio input right 7 blue lead reverse lamp

4 white RCA Audio input left 8 8-pin monitor jack

6. Installation

The car connection should be carried out by a qualified person only.

• Choose a mounting location, depending on the purpose of the monitor. When used to connect backing-

up or parking camera(s), the driver should have a clear view of the display. For all other purposes make

sure the driver is not distracted by images and/or sound from the system.

• Mount the mounting bracket and attach the monitor to the bracket with the screw or install the monitor

in a headrest using the included frame. When choosing the second option, have the installation done by

a qualified person! The dealer will not accept responsibility for any damage to the cars interior.

• Connect the monitor [8] with the monitor.

• Connect a camera/video/DVD… (not incl.) to a video input [1][2]. Connect the sound output of that

device to the audio inputs [3][4].

• Make sure the engine is switched off.

• Connect the red +12VDC power cable [5] to the +12VDC power system of the car. Make sure there

is no power on the connection wire (remove fuse).

• Connect the black ground cable [6] to the car ground.

• The monitor can switch on/over to AV2 automatically when reverse gear is selected. To enable this

functionality, connect the blue reverse cable [7] to the reverse gear power circuit. Make sure there

is no power on the connection wire (remove fuse).Connect the backing-up camera to video input

AV2 [2].

• Apply power to the system (re-insert fuses).

7. Use

• Switch on the monitor by pressing the ON/OFF button on the monitor [G] or remote control ( ).

Note that when connection to the reverse gear system is made, the monitor switches on

automatically when reverse gear is selected.

• Select the video channel (AV1 or AV2) by pressing the video select button on the monitor [F] or

remote control.

• Press the mode select button on the remote control to select the monitor aspect ratio: 16:9 or 4:3.

• Press the menu button [C] on the monitor or remote control to enter monitor setup. Use the menu

button [C] to navigate through the settings; use the up () [D] or down (

) [B] buttons to change

the settings (on the remote control, use the  resp.  buttons).

Menu option setting value

BRIGHT brightness 0 ~ 40

CONTRAST contrast 0 ~ 40

COLOR colour 0 ~ 40

MODE aspect ratio 16:9 or 4:3

TCON image direction LD = normal

RD = mirrored horizontally

RU = mirrored vertically

LU = mirrored horizontally + vertically

LANGUAGE menu language English or Chinese

RESET reset reset monitor to factory defaults

8. Maintenance

• Make sure the monitor is off before performing any maintenance activities.

• Use a soft damp cloth to clean the monitor. Do not apply excessive pressure on the display. Do not

use abrasive solutions or solvents.

9. Battery

Refer to the illustration on page 2 of this manual.

• The remote control uses 1 battery type 3V lithium CR2025 battery (included).

• To (re)place the battery, press on the side of the battery cover [1] and pull [2] to slide it open.

• Insert the battery with the right polarity and close the battery compartment by pushing it back into

the housing of the remote control until it snaps into place.

WARNING:

1 2 3 4 5 6 7 8 9 ... 16 17

Comentarios a estos manuales

Sin comentarios

Velleman MONxTA1 Manual de usuario Pagina 4

Comentarios a estos manuales

Relacionado con productos y manuales para Televisores y monitores Velleman MONxTA1