Velleman WSPT1 Manual de usuario descargar pdf (Pagina 4)

WSPT1 Rev. 02

external sensor

pool temperature

interior view

- bottom

link status indicator

reset button

power on/off button

°C/°F selector

antenna

not used

status LED

battery compartment

to open: turn the top part (with antenna) counter clockwise

6. Use

• Make sure batteries are present inside main station and external sensor (refer to §8).

• When batteries are present, the main unit will display the indoor temperature [A]. To toggle between

°C or °F display, press the °C/°F selector [D].

• Hold the external sensor ±1m (±3ft) from the main station and press the power on/off button [3].

• The local temperature is shown on the display [1]. To toggle between °C or °F display, open the

external sensor by turning the top (with antenna) counter clockwise. Press the °C/°F selector [7].

Verify that the rubber seal is in place and in good condition. Place the top back and secure it by

turning clockwise until you hear a click.

Note: when the external sensor is open, no temperature is measured or displayed.

• The external sensor will now attempt to connect to the main station. The status of the link between

the main unit and external sensor is indicated by the link status indicators on the main unit [C] and on

the external sensor [2]:

steady no signal detection

blinking sending/receiving signal

steady main and external sensor synchronized

• When the main station does not receive a (valid) signal, the outdoor temperature indication [B]

remains blank (--.-). Press the re-sync button [F] to try again.

• The external sensor will send temperature data to the main station every 3 minutes, indicated by a

blinking status LED [5] and blinking link status indicators [2] and [C].

Note: Working frequency is 433MHz. Signal transmission/reception may be interfered by other devices

using the same frequency. If this interference is temporarily, normal operation will resume once

the source of interference disappears.

• Place the main unit indoors, preferably in line-of-sight of the external sensor, but keep at least 1m

(3ft) distance from metal window frames or sources of interference e.g. computer monitors, TV-sets....

Mount the unit on the wall using the wall mounting hole [J] or flip down the foldable stand [H] and

secure it by pushing it inside the housing (see the illustration on page 2).

• Place the external sensor in a pool/hot tub/pond/…, protected from direct sunlight and (heavy) rain.

The maximum distance from the main unit is ±30m (100ft), but distance is reduced depending on the

number, size and type of obstacles between main station and external sensor.

• The maximum and minimum measured temperatures are stored in memory. To recall the memory,

press the max/min button [E] once to see the maximum [A] and minimum [B] indoor temperature.

Press the max/min button [E] again to see the maximum [A] and minimum [B] outdoor

temperature. Press again or simply wait ±10s to return to normal display.

• Press the clear button [G] to clear the maximum and minimum temperature memory.

• To reset the main station, press the reset button [K] which is located under the foldable stand [H] at

the back of the device. This will also clear the stations’ memory and re-initiates the wireless

communication link.

• When the low battery indication appears in the indoor temperature display area [A] or pool

temperature display area [B], replace the batteries of the main station respectively the external

sensor (see §8).

7. Troubleshooting

• No outdoor temperature is displayed.

• Verify whether the external sensor is on. Make sure the batteries of the external sensor are still

sufficiently charged.

• Press the re-sync button [F] and wait ±6 minutes. If this doesn’t help, verify whether the

distance between main station and external sensor is within limits and no interference is present.

1 2 3 4 5 6 7 8 9 ... 30 31

Comentarios a estos manuales

Sin comentarios

Models	Document Type
HRTL12992	User Manual HealthRider HRTL12992 User's Manual, 34 pages
HRCR4896.0	User Manual HealthRider HRCR4896.0 User's Manual, 16 pages
HRSY54370	User Manual HealthRider HRSY54370 User's Manual, 20 pages
HRTL12990	User Manual HealthRider HRTL12990 User's Manual, 34 pages
C895E HRE99940	User Manual HealthRider C895E HRE99940 User's Manual, 32 pages
HREL69011	User Manual HealthRider HREL69011 User's Manual, 24 pages
HREX04981	User Manual HealthRider HREX04981 User's Manual, 16 pages
HRTL07120	User Manual HealthRider HRTL07120 User's Manual, 34 pages
E 530	User Manual HealthRider E 530 User's Manual, 16 pages
E660 HREL09982	User Manual HealthRider E660 HREL09982 User's Manual, 16 pages
HREL2005.0	User Manual HealthRider HREL2005.0 User's Manual, 16 pages
HREL05983	User Manual HealthRider HREL05983 User's Manual, 20 pages
C895E HRE99940	User Manual HealthRider C895E HRE99940 User's Manual, 32 pages
HREL50020	User Manual HealthRider HREL50020 User's Manual, 24 pages
C515e HREL3006.0	User Manual HealthRider C515e HREL3006.0 User's Manual, 20 pages
HREL11900	User Manual HealthRider HREL11900 User's Manual, 20 pages
HRSY23080	User Manual HealthRider HRSY23080 User's Manual, 29 pages
HRCCEL59930	User Manual HealthRider HRCCEL59930 User's Manual, 28 pages
R850x	User Manual HealthRider R850x User's Manual, 24 pages
831.28577	User Manual HealthRider 831.28577 User's Manual, 16 pages

Velleman WSPT1 Manual de usuario Pagina 4

Comentarios a estos manuales

HealthRider HRTL77105 manuals

Healthrider HRTL77105 User Manual (30 pages)

Table of contents

More products and manuals for Fitness, gymnastics & weight training HealthRider

Velleman WSPT1 Manual de usuario Pagina 4

Comentarios a estos manuales

Relacionado con productos y manuales para Reloj Velleman WSPT1

HealthRider HRTL77105 manuals

Healthrider HRTL77105 User Manual (30 pages)

Table of contents

More products and manuals for Fitness, gymnastics & weight training HealthRider